Garage Floor Epoxy
A hard, sealed film that locks out the alkali dust and survives a garage that sits at 120
Concrete Repair and Coating · Las Vegas, NV
Concrete Repair and Coating in Las Vegas
Spalled edges, cracked aprons, alkali dusting and slabs that ate their last coating — repaired before anything is poured.
What we do.
Every coating starts with the concrete under it. The slab is assessed, prepared and tested before a system is recommended.
- Crack chasing and filling with a rigid epoxy, not a flexible caulk that telegraphs back through the film.
- Spall and edge repair at the apron, where tires and heat do the most damage.
- Grinding off failed coatings and the alkali bloom underneath them.
- A moisture-tolerant primer where the slab reads damp.
Repair time plus one coating day
How it works.
1. Assess the slab. Hammer-tap the field, look for delamination, and test moisture. Repair scope is set from that, not from the square footage.
2. Repair, then coat. Repairs cure first. The coating goes over a slab that is stable.
What changes the schedule. Slab condition, square footage, moisture readings and slab temperature. Above roughly 90 F of slab temperature a standard epoxy loses pot life fast, so sections get smaller and the crew grows — the schedule stretches, the system does not change.
Serving Las Vegas and nearby.
This service is quoted across the valley — Las Vegas, North Las Vegas, Henderson, Summerlin, Spring Valley, Paradise, Enterprise, Green Valley, Centennial Hills, Southern Highlands, Anthem, Mountain's Edge, Skye Canyon, Aliante, Providence, Inspirada, Rhodes Ranch, Whitney, Sunrise Manor and Boulder City.
Other services.
Metallic Epoxy
A poured, flowing floor for interiors — the system that turns a plain slab into something
Flake Systems
The workhorse: a full broadcast of vinyl flake over epoxy, buried in a polyaspartic topcoa
Concrete Polishing
No film, no peel, no bubbles — the slab itself is ground, honed and densified until it hol
Epoxy Countertops
A poured top over an existing counter, or a new substrate, finished as a solid sheet with
Basement Epoxy Flooring
Few basements here, but plenty of converted garages, casitas and storage rooms that need a
Commercial and Industrial
Warehouses, shops, kitchens, dealership service bays and HOA amenity rooms — floors that h
Polyaspartic Coatings
The fast, clear, UV-stable topcoat. In this sun it is the difference between a floor that
Concrete Repair and Coating
Spalled edges, cracked aprons, alkali dusting and slabs that ate their last coating — repa
Common questions.
Is epoxy good for a Las Vegas garage floor?
Yes, if it is installed over a properly ground slab. The two things that fail here are prep and heat. A film laid on a dusting slab over caliche lifts at the apron, and a standard clear ambers under west-facing sun.
Does the heat ruin epoxy?
Cured epoxy handles 104-degree air and a 140-degree slab. What the heat does change is the working time: pot life shortens, so a crew works smaller sections in July than in January.
What is caliche and does it matter?
Caliche is the cemented layer the USDA maps here as a petrocalcic horizon, about seven inches down in the Las Vegas series. It does not hold water, so slabs drain sideways, and the concrete above it cures alkaline, with a pH around 8.4 to 8.6. Moisture-tolerant primers and correct prep handle it.
Do I need a permit?
A residential floor coating rarely needs one. A structural repair, a slab replacement or a commercial fit-out does, and the office that issues it depends on the address: the City of Las Vegas, Clark County, Henderson, North Las Vegas or Boulder City.
What temperature does it need to be?
Between 50 and 85 degrees at the slab for the install. In July that means an early start and a slab that has been shaded, not a floor that is 130 degrees at noon.