Garage Floor Epoxy
A hard, sealed film that locks out the alkali dust and survives a garage that sits at 120
Metallic Epoxy · Las Vegas, NV
Metallic Epoxy Floors in Las Vegas
A poured, flowing floor for interiors — the system that turns a plain slab into something a hotel lobby would not blink at.
What we do.
Every coating starts with the concrete under it. The slab is assessed, prepared and tested before a system is recommended.
- Pigment is dropped into the wet base and moved by hand, so no two pours are the same.
- Full UV-stable topcoat, because a room with west-facing glass in this valley sees real sun.
- Solids that go down at 100 percent, with no solvent smell to sit in a closed house.
- Sealed against alkali creep, which matters on these high-pH slabs.
One to two days, furniture back in 24 to 48 hours
How it works.
1. Pour in one pass. Metallic work cannot be stopped and restarted. The crew works wet to wet across the whole room.
2. Clear over the top. Two coats of UV topcoat, then a cure window of 24 hours before furniture goes back.
What changes the schedule. Slab condition, square footage, moisture readings and slab temperature. Above roughly 90 F of slab temperature a standard epoxy loses pot life fast, so sections get smaller and the crew grows — the schedule stretches, the system does not change.
Serving Las Vegas and nearby.
This service is quoted across the valley — Las Vegas, North Las Vegas, Henderson, Summerlin, Spring Valley, Paradise, Enterprise, Green Valley, Centennial Hills, Southern Highlands, Anthem, Mountain's Edge, Skye Canyon, Aliante, Providence, Inspirada, Rhodes Ranch, Whitney, Sunrise Manor and Boulder City.
Other services.
Metallic Epoxy
A poured, flowing floor for interiors — the system that turns a plain slab into something
Flake Systems
The workhorse: a full broadcast of vinyl flake over epoxy, buried in a polyaspartic topcoa
Concrete Polishing
No film, no peel, no bubbles — the slab itself is ground, honed and densified until it hol
Epoxy Countertops
A poured top over an existing counter, or a new substrate, finished as a solid sheet with
Basement Epoxy Flooring
Few basements here, but plenty of converted garages, casitas and storage rooms that need a
Commercial and Industrial
Warehouses, shops, kitchens, dealership service bays and HOA amenity rooms — floors that h
Polyaspartic Coatings
The fast, clear, UV-stable topcoat. In this sun it is the difference between a floor that
Concrete Repair and Coating
Spalled edges, cracked aprons, alkali dusting and slabs that ate their last coating — repa
Common questions.
Is epoxy good for a Las Vegas garage floor?
Yes, if it is installed over a properly ground slab. The two things that fail here are prep and heat. A film laid on a dusting slab over caliche lifts at the apron, and a standard clear ambers under west-facing sun.
Does the heat ruin epoxy?
Cured epoxy handles 104-degree air and a 140-degree slab. What the heat does change is the working time: pot life shortens, so a crew works smaller sections in July than in January.
What is caliche and does it matter?
Caliche is the cemented layer the USDA maps here as a petrocalcic horizon, about seven inches down in the Las Vegas series. It does not hold water, so slabs drain sideways, and the concrete above it cures alkaline, with a pH around 8.4 to 8.6. Moisture-tolerant primers and correct prep handle it.
Do I need a permit?
A residential floor coating rarely needs one. A structural repair, a slab replacement or a commercial fit-out does, and the office that issues it depends on the address: the City of Las Vegas, Clark County, Henderson, North Las Vegas or Boulder City.
What temperature does it need to be?
Between 50 and 85 degrees at the slab for the install. In July that means an early start and a slab that has been shaded, not a floor that is 130 degrees at noon.